How much does Epoxy & Polyurethane Flooring cost in KL & Selangor?
Use this guide to understand fair Klang Valley pricing before requesting a fixed quote. Final cost depends on measurements, access, materials and the actual site condition.
How much does Epoxy & Polyurethane Flooring cost in KL & Selangor?
Epoxy & Polyurethane Flooring in KL & Selangor starts from RM 22 / sq ft; the 4 published rates below are priced per sq ft. Every figure is confirmed in writing before work starts, while access, materials and site condition move the final number — run the Epoxy & Polyurethane Flooring estimator for an instant ballpark, then send photos and measurements for a fixed written quote.
- Published rate book
- Fixed quote in writing
- No hidden fees
Epoxy & Polyurethane Flooring price list
Every figure in this table is the same published rate our estimators and written quotes use — one rate book, three surfaces, no drift.
| Scope | Our published rate | What's covered |
|---|---|---|
| Self-Levelling Epoxy Floor | From RM 22 / sq ft | Mirror-smooth 2–3mm self-levelling epoxy for residential, showroom, and light commercial floors. |
| Flake / Quartz Broadcast Epoxy | From RM 26 / sq ft | Decorative vinyl flake or coloured quartz broadcast with slip-resistant finish for garages and kitchens. |
| Heavy-Duty Mortar Screed | From RM 38 / sq ft | 5–10mm trowel-applied epoxy mortar for warehouses, factories, and forklift traffic zones. |
| Epoxy Floor Repair & Recoating | From RM 14 / sq ft | Diamond-grinding the existing epoxy, repairing damaged areas, and applying fresh primer + topcoat. |
We don't publish third-party market averages for Epoxy & Polyurethane Flooring. Every figure above is a rate we actually charge and confirm in writing before work starts.
How a Epoxy & Polyurethane Flooring estimate adds up
At typical quantities, 250 × self-Levelling Epoxy Floor at RM 22 / sq ft = RM 5,500, before the condition, access and urgency factors above. The calculator below runs the same math for your exact quantities.
What affects Epoxy & Polyurethane Flooring cost?
We confirm these points before work starts so the quote is clear and approved first.
Where these Epoxy & Polyurethane Flooring prices come from
What to measure before you call
The fastest way to a fixed price: send photos and these measurements on WhatsApp. We confirm the price before dispatch.
Try the Epoxy & Polyurethane Flooring calculator
Answer a few questions and get a ballpark price from the same published rates — including labour and standard materials.
Open the Epoxy & Polyurethane Flooring estimatorNeed an exact Epoxy & Polyurethane Flooring quote?
Send photos, measurements and your area. We confirm the itemised fixed-price quote before work begins.
WhatsApp for QuoteEpoxy & Polyurethane Flooring cost FAQs
What is the starting price for Epoxy & Polyurethane Flooring?
Are your prices fair for KL & Selangor?
Can I get a quote from photos?
Do you charge hidden fees?
How long does epoxy flooring take to install and cure?
Will my epoxy floor turn yellow in the sun?
Can epoxy be applied over existing tiles?
Is epoxy flooring slippery when wet?
The Epoxy & Polyurethane Flooring job, step by step
These are the steps a confirmed Epoxy & Polyurethane Flooring quote covers — the price above buys this work, in this order.
- 01
Substrate Assessment
We inspect the existing concrete for moisture, oil contamination, cracks, and surface profile. We perform a calcium chloride moisture test if needed, and recommend a moisture-mitigating primer if required.
- 02
Diamond Grinding
Industrial walk-behind diamond grinders with vacuum extraction are used to achieve a CSP 3–4 profile. Cracks are routed open and filled with epoxy mortar.
- 03
Primer Application
A penetrating epoxy primer is applied by roller to seal the concrete and create a chemical bond with the body coat. We allow 12–24 hours cure depending on ambient conditions.
- 04
Body Coat / Broadcast
Self-levelling epoxy is poured and spread with a notched trowel or spiked roller. For broadcast systems, decorative flake or quartz is hand-cast to full rejection into the wet body coat.
- 05
Topcoat & Curing
After the body coat cures, excess flake is scraped and vacuumed, and a UV-stable aliphatic polyurethane topcoat is applied in two coats for maximum scratch and chemical resistance.
Other services you might need
Browse our other home services across KL & Selangor — fixed pricing and same-day slots available.