How much does Welding & Metal Fabrication cost in KL & Selangor?
Use this guide to understand fair Klang Valley pricing before requesting a fixed quote. Final cost depends on measurements, access, materials and the actual site condition.
How much does Welding & Metal Fabrication cost in KL & Selangor?
Welding & Metal Fabrication in KL & Selangor starts from RM 280; the 4 published rates below are priced per sq ft, per job, per linear ft. Every figure is confirmed in writing before work starts, while access, materials and site condition move the final number — run the Welding & Metal Fabrication estimator for an instant ballpark, then send photos and measurements for a fixed written quote.
- Published rate book
- Fixed quote in writing
- No hidden fees
Welding & Metal Fabrication price list
Every figure in this table is the same published rate our estimators and written quotes use — one rate book, three surfaces, no drift.
| Scope | Our published rate | What's covered |
|---|---|---|
| Custom Window Grille | From RM 42 / sq ft | Powder-coated mild steel window grille in your chosen design (geometric, classic, or modern). Includes anti-rust primer. |
| Main Gate Fabrication | From RM 2,800 | Custom main gate with mild steel frame, infill design of your choice, and hot-dip galvanised + powder-coat finish. |
| On-Site Welding Repair | From RM 280 | Emergency or scheduled welding repair at your location — broken hinges, gate, grille, railing, or structural steel. |
| Staircase Stringer Fabrication | From RM 420 / linier ft | Custom mild steel staircase stringer fabricated to your measurements, primed and painted for indoor or outdoor use. |
Welding & Metal Fabrication jobs priced after a site visit
These jobs depend on measurement, access or site conditions we can't judge from a message. Send photos on WhatsApp and we confirm a fixed price before work starts.
Iron Works
General wrought iron and mild steel works — decorative panels, brackets, frames, trellises, and bespoke metal pieces fabricated to your drawing.
Metal Grille Installation
Installing fabricated window, door, balcony, or air-well grilles onto existing openings, with anti-rust treatment and matching finish.
Metal Gate Repair
Repairing sagging, rusted, or broken gates — hinge renewal, frame straightening, weld repair, and rust treatment with repaint.
Stainless Steel Railing Fabrication
Stainless steel handrails and balustrades for staircases, balconies, and ramps, welded and polished for indoor or outdoor exposure.
Steel Structure & Awning Fabrication
Mild steel awning, canopy, drying-yard, and carport frames fabricated and installed with primer and weather-resistant finish.
Anti-Rust Treatment & Repainting
Wire-brushing, rust conversion, priming, and repainting of existing grilles, gates, railings, and structural steel to extend service life.
We don't publish third-party market averages for Welding & Metal Fabrication. Every figure above is a rate we actually charge and confirm in writing before work starts.
How a Welding & Metal Fabrication estimate adds up
At typical quantities, 250 × custom Window Grille at RM 42 / sq ft = RM 10,500, before the condition, access and urgency factors above. The calculator below runs the same math for your exact quantities.
What affects Welding & Metal Fabrication cost?
We confirm these points before work starts so the quote is clear and approved first.
Where these Welding & Metal Fabrication prices come from
What to measure before you call
The fastest way to a fixed price: send photos and these measurements on WhatsApp. We confirm the price before dispatch.
Try the Welding & Metal Fabrication calculator
Answer a few questions and get a ballpark price from the same published rates — including labour and standard materials.
Open the Welding & Metal Fabrication estimatorNeed an exact Welding & Metal Fabrication quote?
Send photos, measurements and your area. We confirm the itemised fixed-price quote before work begins.
WhatsApp for QuoteWelding & Metal Fabrication cost FAQs
What is the starting price for Welding & Metal Fabrication?
Are your prices fair for KL & Selangor?
Can I get a quote from photos?
Do you charge hidden fees?
Is powder-coat or enamel paint better for outdoor metal?
Can you match the colour of my existing grilles and gates?
Do you do emergency welding repairs?
What is hot-dip galvanising and do I need it?
The Welding & Metal Fabrication job, step by step
These are the steps a confirmed Welding & Metal Fabrication quote covers — the price above buys this work, in this order.
- 01
Site Visit & Design
We measure, take photographs, capture the design intent (or sketch from a reference), and recommend the right material and finish for the project.
- 02
Quotation & Lead Time
Itemized quote covering material, fabrication labour, finish (primer + powder-coat or enamel), installation, and any access equipment.
- 03
Workshop Fabrication
Components are cut, bent, and welded in our KL workshop. Quality checks are done at every stage. For complex projects we provide progress photos.
- 04
On-Site Installation
Fabricated pieces are delivered, positioned, and welded or bolted on site. We minimize mess and clean up before leaving.
- 05
Finishing & Handover
On-site welds are ground smooth, all surfaces are touched up with anti-rust primer, and the agreed finish is applied. For factory powder-coat items, finishing happens before installation.
Other services you might need
Browse our other home services across KL & Selangor — fixed pricing and same-day slots available.